Proxim wireless ORiNOCO AP-4000MR-LR User's Guide Page 92
- Page / 267
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Advanced Configuration AP-4000MR User Guide
Management
92
Configuration Reset via Serial Port During Bootup
If hardware configuration reset is disabled, the user gets prompted by a configuration reset option to reset the AP to
factory defaults during boot up from the serial interface. By pressing a key sequence (ctrl-R), the user gets prompted to
enter a configuration reset password before the configuration is reset.
NOTE: It is important to safely store the configuration reset password. If a user forgets the configuration reset password,
the user will be unable to reset the AP to factory default configuration if the AP becomes inaccessible and the
hardware configuration reset functionality is disable.
Configuring Hardware Configuration Reset
Perform the following procedure to configure Hardware Configuration Reset and to set the Configuration Reset
Password. See Figure 4-28.
1. Click Configure > Management > CHRD.
Figure 4-28 Hardware Configuration Reset
2. Check (enable) or uncheck (disable) the Enable Hardware Configuration Reset checkbox.
3. Change the default Configuration Reset Password in the “Configuration Reset Password” and “Confirm” fields.
4. Click OK.
5. Reboot the AP.
NOTE: It is important to safely store the configuration reset password. If a user forgets the configuration reset password,
the user will be unable to reset the AP to factory default configuration if the AP becomes inaccessible and the
hardware configuration reset functionality is disable.
Procedure to Reset Configuration via the Serial Interface
1. During boot up, observe the message output on the serial interface.
The AP prompts the user with the message: “Press ctrl-R in 3 seconds to choose configuration reset option.”
2. Enter ctrl-R within 3 seconds after being prompted.
The AP prompts the user with “Press ctrl-Z to continue with normal boot up or enter password to reset configuration.”
If the user enters ctrl-Z, the AP continues to boot with the stored configuration.
3. Enter the configuration reset password. The default configuration reset password is “public”.
- ORiNOCO AP-4000MR 1
- Copyright 2
- Trademarks 2
- OpenSSL License Note 2
- Introduction 9
- Mesh Networking 10
- Mesh Network Configuration 12
- Guidelines for Roaming 13
- HTTP/HTTPS Interface 14
- Command Line Interface 14
- SNMP Management 14
- SSH (Secure Shell) Management 15
- Overview 17
- Power/Ethernet Port LEDs 17
- Power Injector 18
- Serial Connection 18
- Antenna Connectors 18
- Prerequisites 20
- System Requirements 21
- Product Package 22
- Hardware Installation 24
- Step 1: Choose a Location 25
- Step 2: Unpack Shipping Box 25
- Step 3: Assemble the Cable 26
- Apply Teflon 26
- Step 5: Mount the Unit 28
- Step 6: Plug in the Cables 29
- Step 7: Power on the Unit 30
- Step 8: View LEDs 30
- Step 9: Tighten the Cables 31
- Adjusting Tx Output Power 34
- Initialization 35
- Logging In 37
- Using the Setup Wizard 38
- Installing the Software 40
- System Status 43
- Advanced Configuration 44
- Dynamic DNS Support 47
- IP Configuration 48
- DHCP Server 49
- DHCP Relay Agent 51
- Link Integrity 52
- Web (HTTP) Interface 66
- MIB (SNMP) Requirements 66
- VLAN on Ethernet Port 68
- Once this 70
- Management VLAN Configuration 71
- Interface Requirements 71
- Ethernet 76
- Management 82
- IP Access Table 83
- Services 83
- Filtering 94
- Static MAC 95
- Advanced 98
- TCP/UDP Port 100
- Rogue Scan 112
- Figure 4-41 Rogue Scan Screen 115
- Spanning Tree 116
- Storm Threshold 117
- Intra BSS 118
- Packet Forwarding 118
- Priority Mapping 121
- Radius Profiles 125
- Configuring Radius Profiles 126
- RADIUS Accounting 129
- Wireless Domain Configuration 131
- SSID/VLAN/Security 133
- Management VLAN 135
- Uplink VLAN ID Table 136
- Security Profile 137
- MAC Access 143
- Wireless-A or Wireless-B 144
- Monitoring 151
- IP/ARP Table 154
- Learn Table 155
- Interfaces 158
- Station Statistics 161
- Mesh Statistics 163
- Link Test 164
- Commands 166
- TFTP File Transfer Guidelines 167
- HTTP File Transfer Guidelines 167
- Update AP 168
- Update AP via HTTP 169
- Retrieve File 171
- Retrieve File via HTTP 172
- Commands AP-4000MR User Guide 173
- Help Link 176
- Troubleshooting 177
- Symptoms and Solutions 178
- Client Connection Problems 180
- VLAN Operation Issues 180
- CMOB Operation Issues 181
- Power-Over-Ethernet (PoE) 181
- Recovery Procedures 183
- set ipaddrtype static 187
- reboot 0 187
- Related Applications 188
- Command Line Interface (CLI) 189
- General Notes 190
- CLI Error Messages 191
- Bootloader CLI 192
- CLI Command Types 194
- Parameter Control Commands 198
- Using Tables and Strings 202
- Log into the AP using Telnet 204
- Other Network Settings 210
- (Mbits/sec)> 212
- CLI Monitoring Parameters 219
- Parameter Tables 220
- System Parameters 222
- Network Parameters 224
- Interface Parameters 228
- Management Parameters 235
- Filtering Parameters 238
- Alarms Parameters 241
- Bridge Parameters 243
- RADIUS Parameters 245
- Security Parameters 246
- VLAN/SSID Parameters 248
- Other Parameters 248
- CLI Batch File 252
- Reboot Behavior 253
- ProximUnify (PXU) Management 254
- ASCII Character Chart 256
- Specifications 257
- Advanced Bridging Functions 258
- Security Functions 259
- Network Functions 259
- Hardware Specifications 260
- Available Channels 261
- Support Options 264
- Statement of Warranty 266
- Other Information 267
Related products and manuals for Routers Proxim wireless ORiNOCO AP-4000MR-LR
(274 pages)© 2020, manymanuals.com. All rights reserved. | 0.478 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals