Proxim wireless ORiNOCO AP-4000MR-LR User's Guide download pdf (Page 80)

Advanced Configuration AP-4000MR User Guide

Interfaces

Mesh Link Parameters

To reset these parameters to their default settings, click the Default button.

NOTE: Changes to these parameters require a reboot in order to take effect.

• Maximum Active Mesh Links: Select a number between 1 and 32 to configure the number of Mesh links that can be

connected to a single Mesh portal or Mesh AP, as follows:

– Mesh Portal: This number represents the maximum downlinks to Mesh APs (up to 32).

– Mesh AP: This number includes one mandatory uplink to the Mesh Portal, with the remaining links (up to 6)

available for downlinks to Mesh APs. A mobile Mesh AP should be configured to 1 to allow only uplinks.

– Proxim recommends a maximum of 30-40 APs total per portal (whether connected directly to the Portal or to

another Mesh AP). See Mesh Network Configuration.

• Maximum Hops to Portal: Set the maximum number of hops (1 to 4) allowed to reach the Mesh portal.

• Hop Factor: This parameter specifies how much weight should be given to the number of hops (vs. RSSI and

Medium Occupancy) when determining the best path to the Mesh Portal. The range is 0 to 10. Set the value to a

higher number to give more weight to this factor; set this value to a lower number to give less weight to this factor.

Setting this value to a lower number is beneficial in applications where an AP roams because of signal strength.

• RSSI Factor: This parameter specifies how much weight should be given to RSSI level (vs. number of hops and

Medium Occupancy) when determining the best path to the Mesh Portal. The range is 0 to 10. Set the value to a

higher number to give more weight to this factor; set this value to a lower number to give less weight to this factor.

• Medium Occupancy Factor: This parameter specifies how much weight should be given to Medium Occupancy level

(vs. number of hops and RSSI) when determining the best path to the Mesh Portal. The Medium Occupancy level is

the amount of wireless traffic on the channel. The range is 0 to 10. Set the value to a higher number to give more

weight to this factor; set this value to a lower number to give less weight to this factor.

• Receive Signal Strength Cut-Off: This parameter specifies the minimum level of received signal strength needed for

the node to be considered a Mesh link. If the Receive Signal Strength at the node is below this level, it is not

considered a link. Set this value to a number between 0 and 26 (dB).

• Roaming Threshold: The Roaming Threshold is the point at which the AP roams or chooses another link. The

threshold number is the difference between two path costs; if the difference is larger than the roaming threshold, the

AP roams; if the difference is smaller than the roaming threshold, the AP maintains its connection with the current link.

The range is 1 to 100. In a static Mesh environment, set this parameter to a high value to avoid switching links too

frequently. In a mobile Mesh environment, set this parameter to a lower value (1 - 20) to allow optimal link

establishment. Note that this parameter has no effect in Mesh Portal mode.

• User Defined Cost: This parameter allows the user to manually add cost to the overall path cost, in order to force

connection to one AP over another.

Auto Switch Mode Parameters

Auto Switch Mode parameters may be configured only for a Mesh Portal. Auto Switch mode allows an AP configured as

a Mesh Portal to switch its mode to be a Mesh AP if it loses its uplink (Ethernet) connection. If the uplink connection is

regained, the AP will switch back to Mesh Portal mode.

NOTE: Depending on the Ethernet connection, if Auto Switch Mode is enabled, the displayed Current Mesh Mode may

be different from the mode that was actually configured.

NOTE: Changes to these parameters require a reboot in order to take effect.

• Enable Auto Switch Mesh Mode: When enabled, an AP configured as a Mesh Portal can dynamically switch to

functioning as a Mesh AP if it loses its uplink connection.

NOTE: When enabling Auto Switch Mode, Proxim recommends that you also enable Auto Channel Select. ACS is

configured on the Wireless A or Wireless B page. See Wireless-A (802.11a) and Wireless-B (802.11b/g

Radio) for more information.

• Current Mesh Mode: Displays the current Mesh mode of the AP (Mesh Portal or Mesh AP).

1 2 ... 75 76 77 78 79 80 81 82 83 84 85 ... 266 267

Comments to this Manuals

No comments

Proxim wireless ORiNOCO AP-4000MR-LR User's Guide Page 80

Comments to this Manuals

Related products and manuals for Routers Proxim wireless ORiNOCO AP-4000MR-LR