Proxim wireless ORiNOCO AP-4000MR-LR User's Guide Page 122
- Page / 267
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Advanced Configuration AP-4000MR User Guide
QoS
122
Figure 4-46 Add Priority Mapping Entry
3. Select the 802.1p Priority (from 0-7) for 802.1d Priorities 0-7.
4. Click OK.
5. Click Add in the IP Precedence/DSCP ranges and 802.1d Priority table.
6. Select the IP DSCP Range for each 802.1d Priority.
7. Click OK.
NOTE: Changes to Priority Mapping require a reboot of the AP to take effect.
Enhanced Distributed Channel Access (EDCA)
WME uses Enhanced Distributed Channel Access, a prioritized CSMA/CA access mechanism used by WME-enabled
clients/AP in a WME enabled BSS to realize different classes of differentiated Channel Access.
A wireless Entity is defined as all wireless clients and APs in the wireless medium contending for the common wireless
medium. EDCA uses a separate channel access function for each of the Access Categories (Index) within a wireless
entity. Each channel access function in a wireless entity that contends for the wireless medium as if it were a separate
client contending for the wireless medium. Different channel access functions in a given Wireless Entity contend among
themselves for access to the wireless medium in addition to contending with other clients.
STA EDCA Table and AP EDCA Table
This page is used to configure the client (STA) and AP Enhanced Distributed Channel Access (EDCA) parameters. You
can modify the EDCA values for both Wireless A and Wireless B.
The EDCA parameter set provides information needed by the client stations for proper QoS operation during the wireless
contention period. These parameters are used by the QoS enabled AP to establish policy, to change policies when
accepting new stations or new traffic, or to adapt to changes in the offered load. The EDCA parameters assign priorities
to traffic types where higher priority packets gain access to the wireless medium more frequently than lower priority
packets.
NOTE: Default recommended values for EDCA parameters have been defined; Proxim recommends not modifying
EDCA parameters unless strictly necessary.
Perform the following procedure to configure the Station and AP EDCA tables.
1. Click Configure > QoS > EDCA.
- ORiNOCO AP-4000MR 1
- Copyright 2
- Trademarks 2
- OpenSSL License Note 2
- Introduction 9
- Mesh Networking 10
- Mesh Network Configuration 12
- Guidelines for Roaming 13
- HTTP/HTTPS Interface 14
- Command Line Interface 14
- SNMP Management 14
- SSH (Secure Shell) Management 15
- Overview 17
- Power/Ethernet Port LEDs 17
- Power Injector 18
- Serial Connection 18
- Antenna Connectors 18
- Prerequisites 20
- System Requirements 21
- Product Package 22
- Hardware Installation 24
- Step 1: Choose a Location 25
- Step 2: Unpack Shipping Box 25
- Step 3: Assemble the Cable 26
- Apply Teflon 26
- Step 5: Mount the Unit 28
- Step 6: Plug in the Cables 29
- Step 7: Power on the Unit 30
- Step 8: View LEDs 30
- Step 9: Tighten the Cables 31
- Adjusting Tx Output Power 34
- Initialization 35
- Logging In 37
- Using the Setup Wizard 38
- Installing the Software 40
- System Status 43
- Advanced Configuration 44
- Dynamic DNS Support 47
- IP Configuration 48
- DHCP Server 49
- DHCP Relay Agent 51
- Link Integrity 52
- Web (HTTP) Interface 66
- MIB (SNMP) Requirements 66
- VLAN on Ethernet Port 68
- Once this 70
- Management VLAN Configuration 71
- Interface Requirements 71
- Ethernet 76
- Management 82
- IP Access Table 83
- Services 83
- Filtering 94
- Static MAC 95
- Advanced 98
- TCP/UDP Port 100
- Rogue Scan 112
- Figure 4-41 Rogue Scan Screen 115
- Spanning Tree 116
- Storm Threshold 117
- Intra BSS 118
- Packet Forwarding 118
- Priority Mapping 121
- Radius Profiles 125
- Configuring Radius Profiles 126
- RADIUS Accounting 129
- Wireless Domain Configuration 131
- SSID/VLAN/Security 133
- Management VLAN 135
- Uplink VLAN ID Table 136
- Security Profile 137
- MAC Access 143
- Wireless-A or Wireless-B 144
- Monitoring 151
- IP/ARP Table 154
- Learn Table 155
- Interfaces 158
- Station Statistics 161
- Mesh Statistics 163
- Link Test 164
- Commands 166
- TFTP File Transfer Guidelines 167
- HTTP File Transfer Guidelines 167
- Update AP 168
- Update AP via HTTP 169
- Retrieve File 171
- Retrieve File via HTTP 172
- Commands AP-4000MR User Guide 173
- Help Link 176
- Troubleshooting 177
- Symptoms and Solutions 178
- Client Connection Problems 180
- VLAN Operation Issues 180
- CMOB Operation Issues 181
- Power-Over-Ethernet (PoE) 181
- Recovery Procedures 183
- set ipaddrtype static 187
- reboot 0 187
- Related Applications 188
- Command Line Interface (CLI) 189
- General Notes 190
- CLI Error Messages 191
- Bootloader CLI 192
- CLI Command Types 194
- Parameter Control Commands 198
- Using Tables and Strings 202
- Log into the AP using Telnet 204
- Other Network Settings 210
- (Mbits/sec)> 212
- CLI Monitoring Parameters 219
- Parameter Tables 220
- System Parameters 222
- Network Parameters 224
- Interface Parameters 228
- Management Parameters 235
- Filtering Parameters 238
- Alarms Parameters 241
- Bridge Parameters 243
- RADIUS Parameters 245
- Security Parameters 246
- VLAN/SSID Parameters 248
- Other Parameters 248
- CLI Batch File 252
- Reboot Behavior 253
- ProximUnify (PXU) Management 254
- ASCII Character Chart 256
- Specifications 257
- Advanced Bridging Functions 258
- Security Functions 259
- Network Functions 259
- Hardware Specifications 260
- Available Channels 261
- Support Options 264
- Statement of Warranty 266
- Other Information 267
Related products and manuals for Routers Proxim wireless ORiNOCO AP-4000MR-LR
(274 pages)© 2020, manymanuals.com. All rights reserved. | 0.141 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals